XADO GREASE RESTORING

XADO技术，通过正常使用条件下在金属摩擦副表面原位生成金属陶瓷层，实现对各种机械设备和车辆的免拆精修、节能环保改造、延长寿命处理等。


恢复型润滑脂

　多功能润滑脂 内含XADO再生剂
修复50%的磨损

详细说明：

产品简介：
XADO恢复型润滑脂用于大负载机械设备的恢复。它能在摩擦表面形成金属陶瓷保护层，恢复零部件的原始形状和几何尺寸，延长零部件使用寿命2-4倍。
XADO恢复型润滑脂是国际发明专利产品，其中含有“摩圣”再生剂和EP（Extreme Pressure）极压添加剂。

主要功效：
1、快速修复磨损；
2、补偿不超过50%的磨损；
3、延长设备使用寿命；
4、消除划痕和微裂纹；
5、降低振动和噪音；
6、使设备具有承受高转速能力；
7、消除表面缺陷和腐蚀痕迹。


使用方法：
使用专用加油枪加注时，通过油枪口直接将润滑脂挤入所要润滑的设备，直至润滑脂到达润滑部位的空隙为止；
手工涂抹时，先清除旧润滑脂，然后用新润滑脂填充轴承空腔至一半即可。

备注：
该润滑脂的特长是对轴承提供全面抗磨损保护（转速不超过10 000r/min）；
对于需周期性更换润滑脂的设备，建议以后使用XADO保护型润滑脂；
可与各种汽车或者工业设备锂基润滑脂混合使用，比例不限。

技术指标：
外观颜色　　 ┉┉┉　　绿色
NLGI 稠度级别　　┉┉┉　 3
点滴温度，℃　 　┉┉┉　 ＞193
25℃时针入度，mm-1 ┉┉┉ 255
120℃时蒸发度，% ┉┉┉　＜0.65
工作温度，℃ 　
长期 ┉┉┉ ＜130
短时间 ┉┉┉ ＜15

四球机上的润滑性能试验数据（20±5℃）：
粘结荷载，N ┉┉┉ ＞2068
极限荷载，N ┉┉┉ ＞980
磨损系数，mm ┉┉┉ ＜0.7
备注：上表中仅列典型参数

标准：
XADO 恢复型润滑脂满足下列标准：
NLGI 3 （ASTM D217）
ISO-L-XBCEB 3 （ISO 6743-9）
KP3K-20（DIN 51502）

包装：
400毫升：气雾剂罐；




Grease 'Restoring'

XADO Grease “Restoring” is designed for restoring of units and mechanisms operating under heavy loads. The grease forms a new cermet layer on friction surfaces: the parts grow in volume and restore their original geometry. It extends the life span of the parts considerably.



Advantages

• eliminates wear quickly;
  
• prolongs life span of units;
  
• eliminates scratches and microcracks;
  
• reduces noise and vibration;
  
• rejects heat from friction areas;
  
• can stand high rotation speed;
  
• compensates 50% wear;
  
• eliminates corrosion and protects units from hostile environment.
  

Technical characteristics

The patented formula of this up-to-date grease is based on a composition of XADO revitalizant and EP complex (Extreme Pressure).




Practical experience:


The main object of any tube-rolling mill is a tube mill. A gear of the driving unit of tube mill “Ural-2M” set at Dnepropetrovsky tube-rolling mill was produced more than 30 years ago. It expended its resource during years of operation. Wear of gears was about 30% in thickness!

The gear surface was covered with scratches and bubbles 4 mm deep.

The wear progressed, the unit needed urgent repair. But the production of this equipment was stopped in Ural. They asked other plants for assistance but after having studied the construction of the equipment they realized that they could not help. The engineers of one plant agreed to manufacture the needed units but their production would take 3 years.

For that the engineers had to invent something in order to stop the wear of the tube mill and keep the unit in a working condition at least for three years until a new gear for this unit was produced. Thus revitalization was the only possible way to solve the problem. The gear was treated with XADO grease Restoring and operated in a regular mode.

The unit was stopped in 526 hours of operating. After having examined the gear it turned out that the gear started to recover! Small scratches and bubbles on the gear surface disappeared, the wear was stopped! The measurements showed that a cermet layer - 400-600 mkm thick (more than half a millimeter) - was formed on the surfaces of the gears.

As a result the plant had not only a three years reserve but also improved performance level of the mechanism.
For example the electricity consumption reduced by 26,6% at idling and by 12,5% under loads.



Method of application:

Remove the old grease.


Fill 1/2 of unit volume with XADO Grease “Restoring”.



Note!

The grease is especially effective for restoration and protection of bearings from wear (up to 10,000 rpm).
If assembles require periodical grease changing you should use XADO Grease “Protective” later on.


Colour: green
Thickener/Base Oil: Li-soap/Mineral Oil
Penetration: 220-250
Category temperature range °C: -40...+120